After using the NST1024 for the last few weeks around the yard we found it to be really useful and much more enjoyable to use than one of those noisy gas models.
The 24 volt battery delivers plenty of power to cut through common grass trimming tasks. In fact, we used it to trim around all of our walks, flower gardens, trees and the house on a single charge.
One of the nice features is the ability to easily switch from Normal mode to Boost mode. This allows you to get a longer run time in normal mode while having the ability to step up the speed for tough spots like tall wet grass. Another feature we liked was the ability to also use other 18V batteries that Black & Decker makes.
Another feature that we like is the Edging Mode. String trimmers are really great for edging flower gardens, walks and driveways. However its usually quite awkward to perform with a string trimmer unless you’re really good at holding it upside down! The Edging Mode makes the task simple and comfortable.
The cutting head of the NST1024 can be rotated 180 degrees which puts the cutting string at 90 degrees to the edging surface. It also has a handy wire “stand” that helps keep the trimmer off the ground a uniform height which prevents premature wearing of the string. This is a pretty sweet feature and a huge time saver.
The Black & Decker NST1024, 24V String Trimmer is an excellent cordless trimmer for small and medium sized yards. It has plenty of power to get the job done and offers some nice features including the edging mode.
While the NST1024 is slightly heavier than some of the competitors the difference is minimal. Frankly the difference is due to the large 24 volt battery pack which does offer additional power so it’s a decent trade off.
At just over $120 we think the Black & Decker NST1024 is a good value and useful tool. If you’re in the market for a new string trimmer be sure to give this cordless version a look.
If you’d like to buy this trimmer you can buy it at Black & Decker’s Site or Amazon. For a limited time (until June 19th) you can enter for a chance to win one of these trimmers here.
Which is Better a Stick Nailer or Coil Nailer? Framers have many choices in nailers…
Estimating How Many Nails for a New Roof When it comes to estimating materials for…
Composite / PVC Decking Layout Tips and Advice Composite and PVC decking have really changed…
Benefits of ERV Systems (Energy Recovery Ventilator) If you're building a new home or doing…
Vermiculite Attic Insulation If your home was built before 1990 there is a chance it…
Arc Fault (AFCI) Circuit Breakers Tripping Often An arc-fault circuit interrupter (AFCI) or arc-fault detection…
View Comments
Love the auto line feed! No more bumping sounds good to me!
Black and Decker AFS spools often feed too much line. I don't feel like doing a video, would you mind doing one? I recently figured out how to repair this and I am unable to find a video documenting the fix. The AFS auto feed spool is used on many trimmers. If you remove the spool there is a small lever underneath. Pull the lever out and you will find extra plastic under the long end that creates a centrifugal counterweight. If the line is feeding out too much then sand or grind this extra plastic off the bottom of the lever almost all the way, until it is almost level with the rest of the lever. Now the feed will not activate until the string is significantly shorter. Insert the lever back into the spool head. Also, there is a small pin protruding from the lever once it is installed that engages with the spool. Grind a small notch for this pin to rest in on the underside of spool, in each tooth all the around the outside on the bottom of the spool. I am guessing my notches are 1/64 to 1/32 of an inch deep. This will cause the afs centrifugal mechanism to be less sensitive to any change of speed. I did this on a black and decker nst1024 24v string trimmer. It was easy to get it right on the first try. I took 25% of the extra plastic off the first time and the rest after one test run. To test the modification iInstall 4 or 5 wraps of line on the spool and see how long it takes to run out of string. If you need me to send you pics you can send me an email at v---rep***peto*@****gmail.com without the * or - . If I remember I will probably send them to you anyway next time I am out in the shop with my phone. I forgot to weigh the lever before I started grinding. Let me know how much it weighs if you have a scales.